the most common question in spring repair, answered honestly. On a two-spring door, one snapped spring means its partner has done identical work - this gui
Call +1 (214) 774-5947View Spring Services
the most common question in spring repair, answered honestly. On a two-spring door, one snapped spring means its partner has done identical work - this guide explains the balance argument, the labour argument and the rare cases where replacing a single spring is genuinely reasonable.
A garage door spring is not a small part doing a small job. On a typical Dallas home the springs carry almost the entire weight of the door, which can be well over a hundred pounds on an insulated double door. The opener is really only guiding that weight - the springs do the lifting. That is why should you replace one spring or both? matters so much: when the spring system is correct, the door feels light, travels evenly and the opener lasts for years. When it is wrong, every part of the system suffers, from the cables and rollers to the opener motor itself.
North Texas adds its own pressures. Long hot summers dry out lubrication and make metal expand and contract daily, dust works into coils and bearings, and the sudden temperature swings of a Texas cold snap can be the final cycle for a spring that was already tired. Many Dallas doors are also heavy insulated models fitted for energy efficiency, and heavier doors ask more of their springs on every single cycle. Our technicians see these patterns every week, which is why we size springs from the actual door in front of us - its weight, height, track type and drum size - rather than from a guess or from whatever spring happens to be on the truck.
Good spring work also follows a strict order. The door is secured, tension is released in a controlled way with winding bars, the old hardware is inspected rather than simply removed, and the replacement spring is matched by wire size, coil diameter and length. After fitting, the door is balance-tested at several heights: a correctly balanced door should stay where it is left, lift with modest effort and close without slamming. Finally the opener's force and travel settings are checked, because an opener adjusted for a tired spring will push too hard against a healthy new one. That full process is what turns a parts swap into a repair that lasts.
Guides are useful, but a spring system is judged on the actual door. When our Dallas technicians attend a home, they measure the existing springs, weigh the door's lift, check cables and drums, and test the balance by hand before recommending anything. That habit - measure first, advise second - is what this guide is really recommending to every homeowner: decisions about springs should come from the condition of your door, not from habit, guesswork or the loudest advert.
Technician note: If anything in this guide matches what your door is doing - heaviness, noise, a visible coil gap, rust - the safest next step is a spring inspection. Most inspections end with a small fix or simple reassurance, and both are better than an emergency.
Springs are not a side job for us - they are the main job. That focus means correct sizing, correct tension and a door that stays balanced long after the visit.
A broken spring traps cars and leaves homes unsecured. We keep same-day slots across Dallas and answer emergency calls around the clock.
We weigh and measure your door and match the wire size, coil diameter and length to it. A spring that is even slightly wrong makes the opener work too hard and wears out early.
Winding bars, locking pliers and proper unloading of tension on every job. We never cut corners on the most dangerous part of a garage door system.
Cables, drums, rollers, tracks and opener force are checked while we are there, because a spring rarely fails in a system where everything else is perfect.
We show you the failed spring, explain the options - including replacing one spring or both - and only start when you are happy with the plan.
Professional spring repair is mostly about using the right tool for a job where a mistake can hurt someone. Below are the tools our Dallas technicians carry for this work, and what each one actually does on your repair.
Solid steel winding bars are the only safe way to add or release torsion spring tension, quarter turn by quarter turn. We use bars matched to the winding cone size - never screwdrivers or makeshift substitutes, which can slip and cause serious injury.
Locking pliers clamp the torsion shaft and the track during a repair so the door and shaft cannot move unexpectedly while springs are off. They are a simple tool that prevents the sudden movements that make spring work dangerous.
Set screws, lag bolts, bearing plates and centre brackets all need the correct socket sizes. The right fit matters because the centre bracket carries the full spring load into the wall framing above your door.
We measure wire diameter, inside coil diameter and overall spring length precisely before ordering or fitting a replacement. Guessing a spring size is how doors end up heavy, fast or unbalanced.
Used for fasteners, brackets and hardware - never for winding springs. It speeds up the safe parts of the job so more of the visit goes into careful tensioning and testing.
A stable ladder gives the technician a safe working position at the spring line above the door. Most spring injuries involve poor footing or reaching, so ladder placement is part of our setup on every job.
Every spring job follows the same careful pattern: secure the door, release tension safely, fit the correctly sized spring, then balance and test. These sample photos show the kind of before and after result Dallas homeowners can expect.
Winding bars, locking pliers, a spring sizing gauge and the correct socket set are standard on every truck. Using the proper tools is what makes the difference between a spring that is simply fitted and a spring that is fitted, tensioned and balanced correctly.
"The door kept stopping a few inches up. It turned out one spring had lost tension and the other was cracked. Both replaced, door rebalanced, and they showed me how the balance test should look. Great service."
Carlos R. - Richardson, Dallas
"I liked that they explained the difference between spring types before starting. We chose oil-tempered springs and the door balance is spot on. Friendly technician, tidy work, and a proper safety check at the end."
Jennifer P. - Irving, Dallas
"Our torsion spring snapped at 7 in the morning and the car was trapped inside. They answered straight away, arrived the same day, replaced both springs and balanced the door perfectly. It lifts smoother now than it has in years."
James W. - Preston Hollow, Dallas
Read more on our reviews page.
If your Dallas door has two springs and one has snapped, the second spring has done exactly the same number of cycles and is usually close to failing too. Replacing both together keeps the door balanced and avoids a second emergency visit soon after.
Please do not try. The opener is not built to lift the full weight of the door, and forcing it can burn out the motor, strip gears or bend the top panel. Keep the door closed and let a technician release and repair it safely.
Springs are rated in cycles - one open and close is one cycle. Standard springs commonly serve many years of normal family use, while high-cycle springs are built for much heavier use. Texas heat, rust and heavy insulated doors all shorten spring life, which is why an annual balance check is worthwhile.
We strongly advise against it. A wound torsion spring stores a large amount of energy, and releasing it with the wrong tools is one of the most common causes of serious garage injuries. The spring itself is not the expensive part of this job - safe handling and correct balancing are what you are paying for.
Our main spring repair service - broken and tired springs fixed, sized and balanced.
Correctly measured torsion springs, wound to the right tension for your door.
Around-the-clock help when a spring failure traps your car or leaves your home open.
Call now and talk to a real person. Same-day spring repair slots in Dallas fill fast, and emergency help is available around the clock.
Call +1 (214) 774-5947